How To Remove Seats From Honda Accord

Honda Accord: Front end Seat Removal/Installation

Special Tools Required

KTC Trim Tool Set SOJATP2014*

*Available through the Honda Tool and Equipment Programme; call 888-424-6857

SRS components are located in this area. Review the SRS component locations, two-door (come across page 24-23), iv-door (encounter folio 24-21) and the precautions and procedures (see page 24-25) before doing repairs or service.

Do the ODS unit initialization (meet page 24-40), afterward front passenger's seat replacement.

Notation: - Put on gloves to protect your hands.

- Take care not to scratch the body or tear the seat - Use the appropriate tool from the KTC trim tool set to avert impairment when removing components.

1. Adjust the steering column to the full tilt upwardly position, and to the full telescopic in position. Adjust the seat-dorsum recline to a eye position.

2.2-door rider'south seat: Advisedly insert the tip of a small screwdriver (A) through the hole in the back of the front seat belt lower anchor cover (B), and into the hole in the forepart seat belt lower anchor (C). Unlock the lower anchor by pushing in on the screwdriver.

Remove the screwdriver, and then detach the front seat belt anchor plate (D) and the ballast cover from the lower anchor.

3.4-door: Slide the front seat all the way forward.

3.4-door: Slide the front seat all the way forwards.

Carefully pry upwardly on the bottom of the anchor comprehend (A) at the pry point (B) with the appropriate trim tool to release the hooks (C) and the tab (D), then remove the cover by pulling it upward.

Commuter'south seat

Passenger's seat

Passenger's seat

4.4-door: Remove the lower anchor bolt (A).

4.4-door: Remove the lower anchor commodities (A).

5. Remove the seat track end covers (A) from the back of

5. Remove the seat rail cease covers (A) from the back of both seat tracks.

2-door driver's seat (10-way ability seat)

2-door driver's seat (manual height adjustable seat)

ii-door driver'southward seat (transmission acme adjustable seat)

6. Remove the seat mounting bolts from the rear side of

half-dozen. Remove the seat mounting bolts from the rear side of the front end seat.

7. Slide the front seat all the way back, and remove the

seven. Slide the front seat all the way back, and remove the seat mounting bolts.

8. Do the battery terminal disconnection procedure (see

eight. Practise the battery final disconnection procedure (see page 22-91), then expect at least 3 minutes before removing the seat.

9. Lift upwardly the front seat, and then disassemble the harness clips (A).

Disconnect the flooring wire harness connector (B) (except driver's seat (manual height adjustable seat)), the side airbag connector (C), and the seat belt buckle switch connector (D). Driver's seat (manual height adaptable seat): Disconnect the seat position sensor connector ( Due east ).

2-door driver'south seat (10-way power seat)

2-door driver's seat (manual height adjustable seat)

two-door driver'southward seat (manual height adaptable seat)

2-door passenger's seat

ii-door passenger's seat

4-door driver's seat (10-way power seat)

4-door driver's seat (10-mode ability seat)

4-door driver's seat (manual height adjustable seat)

iv-door driver'south seat (manual summit adaptable seat)

4 door passenger's seat

iv door passenger's seat

10. Remove the head restraint

ten. Remove the head restraint 11. With the assist of an assistant, carefully remove the front seat through the front door opening.

12. Install the front seat in the reverse order of removal, and note these items: - If the prune are damaged or stress-whitened, replace them with new ones.

- Push the clips and the hooks into place securely.

- Tighten the bolts by hand showtime, so tighten them to specified torque.

- Tighten the seat mounting bolts to the specified torque in the sequence shown. Slide the seat all the fashion dorsum and tighten and
and tighten and , then slide it forward
and tighten . The driver's seat is shown; and
the passenger's seat is similar. . The driver'south seat is shown;
the passenger'southward seat is similar.

- Make sure each connector is plugged in properly.

- Practise the battery last reconnection procedure (see folio 22-91).

- The triangle marks (A) on the anchor plate (B) and the lower ballast (C) must face up the same side. Insert the ballast plate into the lower anchor, and brand sure that it is locked securely.

Seat mounting bolts tightening sequence

2-door passenger's front seat belt lower anchor

2-door passenger's forepart seat belt lower ballast installation

Front Seat Recline Motor Replacement

Front Seat Active Caput Restraint Inspection

NOTE: If the vehicle has been in a collision, always audit the active caput restraint, even if they appear reusable, past doing the following procedure. 1. Driver'due south seat (manual height adjustable ...

Front Seat Recline Motor Replacement

Driver's Seat (10-mode Power Seat) SRS components are located in this surface area. Review the SRS component locations, ii-door (run across page 24-23), four-door (come across page 24-21) and the precautions and procedures ( ...

See as well:

Turn Signals
The turn signals can be used when the ignition switch is in ON . • One-bear upon turn betoken When you lightly push up or downwardly and release the plough signal lever, the exterior turn signals and t ...

Driver's Dashboard Lower Cover Removal/Installation
Special Tools Required KTC Trim Tool Set SOJATP2014* * Available through the Honda Tool and Equipment Program; call 888-424-6857 NOTE; - Have care non to scratch the dashboard or the related p ...

HomeLink® Universal Transceiver*
The HomeLink® Universal Transceiver can be programmed to operate upward to three remote controlled devices around your home, such every bit garage doors, lighting, or home security systems. • Important S ...

Source: https://www.haccord.org/front_seat_removal_installation-1319.html